July 13, 2008
How to break in a Nitro RC engine Part 3
This vid is on how to start your RC truck buggy or truggy. I will walk you through using a ez starter, roto starter, bump box, tiger drive, and pull start. i will show you how to prime the kit via the fuel piping, the pipe, and other starting devices. then, at the end, I will show you that these methods really do work.
This is a ten video rc nitro break in series. The series is designed on how to guide the novice to experienced racing pro or basher on how to break in a nitro rc properly. I will teach the traxxas, new school, and my own method which is a combination of the other two. I will show the user how to prime a nitro rc engine, start the engine using a bump start box, ex starter, roto start, pull start and tiger drive devices. Then, after break in, I will go over nitro engine tuning theory and then show the tuning actally done. This engine tuning series is good for the AE associated electronics Gt GT2 MGT mini MGT hpi savage x ss, traxxas revo tmaxx t maxx s ofna hyper st pro 7 8 9 8. buggy truggy jammin crt crt.5 mini hyper losi lst lst2 lst1 muggy 8ight 8ight-t truggy monster truck mt byt chris mt kyosho 777 sp2 worlds mugen mbx lx comp pro and many more! os engines trx picco sts axial .12 .15 .18 3.3 2.5 .20 .21 .23. 25. 27 .28 .30 .32 collari lrp spec 3 DM
Duration : 0:6:28
Filed under RC Engines by Ray
Comments on How to break in a Nitro RC engine Part 3 »
If it turns right …
If it turns right then no. Look at the servo. You may not have "straight ahead" set for the center of the servo. You might also have binding or something in the steering line.
thx dude
but my …
thx dude
but my buggy dont wanna swing to the left…
can it be the batteries?
thanks i fixed it
thanks i fixed it
Is the piston …
Is the piston moving? Is the flywheel on tight? Is the engine primed? Do you have a good glow plug and all batteries charged? Do you have too much or too little compression?
hey does anyone …
hey does anyone know why my dragster wont start on a starter box the fly wheel is turninng but it wont start
Oh wow!!! Geez, …
Oh wow!!! Geez, thanks for the info! I have been in the hobby for over 15 years and had no idea what a carb was! Thank you!!
FYI- The HSN nozzle that allows fuel into the carb and needle is referred to as an…. *INLET* and if you watch the vid, then that is where the fuel is going and where to watch for the fuel.
The vid is correct and so is the terminology. Sorry bud!
just so you know it …
just so you know it is called a carbeurator, not an inlet. LOL
Hello! There are …
Hello! There are several ways to prime. The blowing method will work on any style of starter. If you are using a ez starter or bump box then cover the tip of the pipe, use the starter, and then stop when the fuel touches the inlet to the HSN.
Also, keep in mind that a good cooling head, rich settings, and anything else that will put it into a rich "cant get heat right away" environment will delay starting. For that, preheat with a hair dryer or heat gun.
wow dude ur a god …
wow dude ur a god at nitro engines dude plz reply to me how i can get my hpi savage s-25 pull start engine to start it decently tuned but my truck wont start it not flooded fully charged glow ignitor but how u said to start it by blowing into that tube is that the real only good way to prime ur engine casue on my gas tank it has a primer should i use it or ur way?
Pretty much! =)
Pretty much! =)
that started easy,i …
that started easy,i dont have a nitro but others ive seen have to keep pulling to start,is that cuz theve not primed it correctly?
There are many …
There are many theories on break in and they all change a little. I just picked the top two and added my own. =)
i was watchingin …
i was watchingin your vid u forgot auther way of for break in is heat cycleing
Losi 8ight
Losi 8ight
what car is that
what car is that